FS LITE TRAINER II SERIAL
FS LITE TRAINER II PRO

The GPS coordinates come in two flavors which can't be distinguished programmatically, to switch from one to the other add 2 to the Option/FixedID setting value (0->2, 1->3). unless on OpenTX 2.3.3+ you use the 'Disable channel mapping' feature on the GUI.ДЇull telemetry is available if the RX supports it: TX_RSSI, A1 (set the ratio to 12.7) and A2 (set the ratio to 12.7), VFAS, RPM, temperature 1&2, GPS position/speed/altitude/time. RX output will match the Devo standard EATR independently of the input configuration AETR, RETA. DEVO - 7Д®xtended limits and failsafe supported CH1 This is required in rare cases where some CYRF6936 modules and/or RXs have an inaccurate crystal oscillator. If USE_CYRF6936_CH15_TUNING is enabled, the value of channel 15 is used by all CYRF6936 protocols for tuning the frequency. Option is used to select between WBUS=0 and PPM=1 Telemetry enabled for A1=RX_Batt (Ratio 12.7), A2=Ext_Batt (Ratio 12.7), RX RSSI, TX RSSI, TX LQI (100=all telem packets received.0=no telem packets). Models: Axial SCX24: Deadbolt, Jeep Wranger Rubicon, Chevrolet 1967 C10, B-17 Betty and Panda Hobby: Tetra K1, X1, X2ДЇailsafe fully supported (value, hold and no pulse). TX: Axial AX-4 2.4GHz transmitter and Panda Hobby 3CH Smart Radio 2.4GHz (MT-305A) Only 1 frequency hopping table Sub_protocol SCX24 - 2

FS LITE TRAINER II PRO

Models: TX: CADET PRO V4, RX: RX-602 V4 Sub_protocol Lite - 1 unless on OpenTX 2.3.3+ you use the 'Disable channel mapping' feature on the GUI. RX output will match the Pelikan standard AETR independently of the input configuration AETR, RETA. RX output will match the Hype standard AETR independently of the input configuration AETR, RETA. Surface protocol called FHSS introduced in 2017. Once activated, any bind will only happen if all these elements are happening at the same time:.

FS LITE TRAINER II SERIAL

Bind on channel can be locally enabled/disabled by setting 'Bind on channel' or 'Autobind' per model for serial or per dial switch number for ppm.Any channel between 5 and 16 can be used by configuring BIND_CH in _config.h. Bind on channel can be globally enabled/disabled in _config.h using ENABLE_BIND_CH.In case a protocol is not autobind but you want to enable it, change the 'Autobind' or 'Bind on channel' on OpenTX setting to Y for the specific model/entry. In these protocols you do not need to press the bind button at power up to bind, it will be done automatically. This is for models where the receiver expects to rebind every time it is powered up. Autobind protocol - The transmitter will automatically initiate a bind sequence on power up or model/protocol selection.Italic numbers are referring to protocol/sub_protocol numbers that you should use if the radio (serial mode only) is not displaying (yet) the protocol you want to access.Otherwise it will be truncated to -100%.+100%. Extended limits supported - A channel range of -125%.+125% will be transmitted.Channel ranges - A radio output of -100%.0%.+100% will match on the selected protocol -100%,0%,+100%.

The module will take whatever input channel order you have choosen and will rearrange them to match the output channel order required by the selected protocol. You can change this in the compilation settings or by using a precompiled firmware.

Channel Order - The channel order assumed in all the documentation is AETR.

The Deviation project (on which this project was based) have a useful list of models and protocols here. If you want to see examples of model configurations see the Models page. Here are detailed descriptions of every supported protocols (sorted by RF modules) as well as the available options for each protocol.

Fs lite trainer ii